Floatboxx 14-Core Power Cable for VESC Projects
This is the exact cable available from Floatboxx: https://www.floatboxx.com/product/12162652/14-core-battery-cable-vesc
Floatboxx was kind enough to allow some U.S./North American distribution, and so some lengths of this cable are available for domestic shipment rates.
This cable is very good, and I use it in custom builds done at the shop. It is a DIY item, and so the necessary skill and care must be taken to strip away insulation and jacketing without damaging the insulation of the internal wires.
Length is approximately 90cm, or about 3 feet.
Here is the information from the Floatboxx site listing:
Dedicated power cable for PEV's and electric skateboards.
14 wires together in 1 waterproof and impactproof PVC sheathing.
Bare cable without connectors. Intended for DYI.
2x AWG13 for discharge +
3x AWG20 for charge/BMS +
4x AWG24 twisted pairs for CAN, LEDs*,...
OD ø11 mm fits nicely in a M20/PG13,5 cable gland.
Maximum 100V - Maximum 90°C (195°F)
Content:
- 1 multicore cable with length 90 cm ~ 3ft
* for LEDs check the required current and if needed combine 2x AWG24 per pole.
AND make a diagram or a picture of your solderings !
This is the exact cable available from Floatboxx: https://www.floatboxx.com/product/12162652/14-core-battery-cable-vesc
Floatboxx was kind enough to allow some U.S./North American distribution, and so some lengths of this cable are available for domestic shipment rates.
This cable is very good, and I use it in custom builds done at the shop. It is a DIY item, and so the necessary skill and care must be taken to strip away insulation and jacketing without damaging the insulation of the internal wires.
Length is approximately 90cm, or about 3 feet.
Here is the information from the Floatboxx site listing:
Dedicated power cable for PEV's and electric skateboards.
14 wires together in 1 waterproof and impactproof PVC sheathing.
Bare cable without connectors. Intended for DYI.
2x AWG13 for discharge +
3x AWG20 for charge/BMS +
4x AWG24 twisted pairs for CAN, LEDs*,...
OD ø11 mm fits nicely in a M20/PG13,5 cable gland.
Maximum 100V - Maximum 90°C (195°F)
Content:
- 1 multicore cable with length 90 cm ~ 3ft
* for LEDs check the required current and if needed combine 2x AWG24 per pole.
AND make a diagram or a picture of your solderings !
This is the exact cable available from Floatboxx: https://www.floatboxx.com/product/12162652/14-core-battery-cable-vesc
Floatboxx was kind enough to allow some U.S./North American distribution, and so some lengths of this cable are available for domestic shipment rates.
This cable is very good, and I use it in custom builds done at the shop. It is a DIY item, and so the necessary skill and care must be taken to strip away insulation and jacketing without damaging the insulation of the internal wires.
Length is approximately 90cm, or about 3 feet.
Here is the information from the Floatboxx site listing:
Dedicated power cable for PEV's and electric skateboards.
14 wires together in 1 waterproof and impactproof PVC sheathing.
Bare cable without connectors. Intended for DYI.
2x AWG13 for discharge +
3x AWG20 for charge/BMS +
4x AWG24 twisted pairs for CAN, LEDs*,...
OD ø11 mm fits nicely in a M20/PG13,5 cable gland.
Maximum 100V - Maximum 90°C (195°F)
Content:
- 1 multicore cable with length 90 cm ~ 3ft
* for LEDs check the required current and if needed combine 2x AWG24 per pole.
AND make a diagram or a picture of your solderings !